M505 Slim-Line Rotary Sensor
ATEX & IECEx approved intrinsically safe sensors for hazardous mining environments
This sensor at a glance
Available in any measurement angle from 15° to 160°
Longer operating life than a potentiometer
Fast delivery options available
Body Diameter: 19mm
Sensor Mounting: Flange or servo
Sealed to IP67
< ±0.25% up to 100° at 20°C
< ±0.1 % available on request
Temperature range: -40°C to +80°C
The intrinsically safe M505 is ATEX and IECEx approved for use in potentially explosive gas/vapour, dust atmospheres and mining environments.
It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.
The M505, like all Positek sensors, is supplied with the output calibrated to the angle required by the customer, between 15 and 160 degrees and with full EMC protection built in. The sensor provides a linear output proportional with angle of rotation. There is a machined registration mark to identify the calibrated mid point.
Overall performance, repeatability and stability are outstanding over a wide temperature range. The M505 has long service life and environmental resistance with a rugged stainless steel body, shaft, flange or servo mount. The flange or servo mounting options make the sensor easy to install, it also offers a range of mechanical options. Environmental sealing is to IP67 .
Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.
This sensor is ATEX/IECEx approved to:
Ambient temperature range extended to -40°C to +80°C .
|Galvanic Isolation Amplifier|
Intrinsically safe sensors must be used with a galvanically isolated amplifier with safety parameters not exceeding:- Ui: 11.4V, Ii: 0.2A, Pi: 0.51W. Sensor can be installed with a cable length up to 1000m maximum from the amplifier, cable capacitance and inductance can be up to:- Capacitance: 200 nF max, Inductance: 810 μH max.
Approved amplifiers are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
|Body Length (to seal face)||45.4mm|
|Shaft|| see drawing|
|Measurement range||Any angle from ±7.5° to ±80°|
|Independent Linearity||<±0.25% up to 100° at 20°C|
<±0.1% available on request
|Temperature Coefficient||<±0.01%/°C Gain & <±0.01%FS/°C Offset|
|Output Characteristics||See Graph|
|Operating||-40 to +80°C|
|Storage||-40 to +125°C|
|EMC Susceptibility||EN 61000-6-2 |
|EMC Radiated||EN 61000-6-3|
|Vibration||IEC 68-2-6: 10g|
|Shock||IEC 68-2-29: 40g|
|MTBF||350,000 hrs 40°C Gf|
|Electrical Connections||Screened cable or integral connector|
Positek offers a range of options for its standard sensors. Each sensor is manufactured to suit each customer's preferences. If your requirement is outside the options given below, Positek can modify/ redesign a sensor to suit your specific requirement. Standard options are available as below:
Factory set to any length from ±7.5° to ±80° in increments of 1°. For example, if your application requires 10° measurement, then Positek will manufacture the sensor specifically for this angular range. The sensor will measure 90° however will still rotate through 360°.
|Cable with axial gland, IP67||L (3 core cable)|
LQ (5 core cable)
(click for more information)
|Cable length - The standard length of cable supplied with a Positek position sensor is 50cm although you can specify any length you require up to a maximum of 15,000cm||Specified in cm after the L/LQ e.g. L200 for 200cm cable from axial cable gland|
|<+/-0.1% FSO Linearity error (100° max)||Option Code|