S623 Submersible IP68 350bar Large Angle Tilt Sensor

Position feedback for underwater marine and offshore applications

Underwater

This sensor at a glance

Available in any measurement angle from 15° to 160°

Longer operating life than a potentiometer

Fast delivery options available

Body Diameter: 40mm

Sensor Mounting: Flange

Sealed to IP68 350bar, 3500msw, 5000psi

Independent Linearity/Hysteresis (combined error):
< ±0.25° up to 100°

Resolution: Infinite

Temperature range: -4 to +50°C

The 350bar S623 tilt sensor is an affordable, durable, high-accuracy sensor designed for underwater marine and offshore applications. The S623, like all Positek sensors, is supplied with the output calibrated to the angle required by the customer, between 15 and 160 degrees. The sensor provides a linear output characteristic with angle of deflection. There is a machined registration mark to identify the calibrated mid point.

It is particularly suitable for OEMs seeking good sensor performance for arduous applications such as industrial machinery where cost is important.

Overall performance, repeatability and stability are outstanding over a wide temperature range. It is sealed to IP68 350bar (5000psi, 3500m depth).

The sensor has a rugged stainless steel body and mounting flange. The S623 offers a range of electrical options. Full EMC protection is built in.

Dimensions

Body Diameter
40mm
Body Length (to seal face)
81mm
For full mechanical details see drawing
Measurement Range Any angle from ±7.5° to ±80°
Independent Linearity/Hysterisis (combined error)
<±0.25° up to 100°
Temperature Coefficient
<±0.01%/°C Gain & <±0.01%FS/°C Offset
Output Characteristics
See Graph

Response Time

Damping Ratio

250ms at 20°C typical

0.2:1 (0.6 nom at 25°C)

Resolution
Infinite
Noise

<0.02% FSO


Output Signal and Output Load

Output Signal
Output Load
0.5 to 4.5 V DC ratiometric
5k Ohms min
0.5 to 4.5 V DC
5k Ohms min
± 5V DC
5k Ohms min
± 10V DC
5k Ohms min
0.5 to 9.5 V DC
5k Ohms min
4 to 20mA (2 wire)
300 Ohms max at 24V
4 to 20mA (3 wire sink)
950 Ohms max at 24V
4 to 20mA (3 wire source)
300 Ohms max at 24V
Supply Current
12 mA Typical 20 mA max (voltage versions)


Temperature Limits

Operating
-4 to +50°C
Storage
-4 to +50°C


Other

EMC Susceptibility
EN 61000-6-2
EMC Radiated
EN 61000-6-3
Vibration
IEC 68-2-6: 10g
Shock
IEC 68-2-29: 40g
MTBF
350,000 hrs 40°C Gf
Sealing
IP68 350bar, 5000psi, 3500m
Electrical Connections
Micro wet mate connector

Positek offers a range of options for its standard sensors. Each sensor is manufactured to suit each customer's preferences. If your requirement is outside the options given below, Positek can modify/ redesign a sensor to suit your specific requirement. Standard options are available as below:


Measurement Range

Factory set to any length from ±7.5° to ±80° in increments of 1°. For example, if your application requires 90° measurement, then Positek will manufacture the sensor specifically for this angular range. The sensor will measure 90° however will still rotate through 360°.


Electronic Options

Output Signal
Supply Input
Option Code
Standard


0.5V to 4.5V DC ratiometric
+5V DC nom. ±0.5V
A
Buffered


0.5V-4.5V DC
+24V DC nom. +9-28V
G
±0.5V DC
±15V DC nom. ±9-28V B
0.5-9.5V DC
+24V DC nom. +13-28V
C
±10V DC ±15V DC nom. ±13.5-28V D
4-20mA (2 wire)
+24V DC nom. +18-28V
E
4-20mA (3 wire sink)
+24V DC nom. +13-28V
F
4-20mA (3 wire source)
+24V DC nom. +13-28V
H


Connector/Cable Options

Axial micro wet mate bulkhead and mating connector with 50cm flying head (standard fit).
Mating connector with longer cables available as special.
Option Code
J50
Radial micro wet mate bulkhead and mating connector with 50cm flying head (standard fit).
Mating connector with longer cables available as special.
Option Code
K50
image missing