X133 Mid Stroke Linear Position Sensor

ATEX & IECEx approved intrinsically safe sensors for hazardous gas environments

Linear

This sensor at a glance

Available in any measurement range from 0-51mm to 0-100mm e.g 67mm
(for 2-50mm range see X103)

Longer operating life than a potentiometer

Fast delivery options available

Body Diameter: 35mm

Sensor Mounting: Flange or body clamps

Sprung target option unavailable

Sealed to IP65/67 depending on connector/cable option

Independent Linearity:
< ±0.25%
< ±0.1 % option available

Resolution: Infinite

Temperature range: -40° to +80° C

The intrinsically safe X133 is ATEX and IECEx approved for use in potentially explosive gas/vapour atmospheres. It is designed for a wide range of industrial applications and is ideal for OEMs seeking good sensor performance in situations where a mid-bodied sensor is required for operation in hazardous areas. The unit is compact and space-efficient, being responsive along almost its entire length, and like all Positek sensors provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-51mm to 0-100mm and with full EMC protection built in.

Overall performance, repeatability and stability are outstanding over a wide temperature range.

The sensor has a rugged stainless steel body and plunger. It is easy to install and set up, mounting options include flange and body clamps. The plunger can be supplied free or captive, with female M4 thread, or spring-loaded with a ball end. The X133 also offers a wide range of mechanical options, environmental sealing is to IP65 or IP67 depending on selected cable or connector options.

Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier.  Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.

The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.

Intrinsic Safety

ATEX/IECEx approval
The sensor is ATEX/IECEx approved to:
Ex II 1G
Ex ia IIC T4 GA (Ta = -40°C to +80°C).
This designates the sensor as belonging to; Group II: suitable for all areas except mining, Category 1 G: can be used in areas with continuous, long or frequent periods of exposure to hazardous gas (Zone 0). Protection class ia, denotes intrinsically safe for all zones. Apparatus group IIC: suitable for IIA to IIC explosive gas. Temperature class T4: maximum sensor surface temperature under fault conditions 135°C. Ambient temperature range extended to -40°C to 80°C. Approval only applies to the specified ambient temperature range and atmospheric conditions in the range 0.80 to 1.10 Bar, oxygen <=21%.
Galvanic Isolation Amplifier

Intrinsically safe sensors must be used with a galvanically isolated amplifier with safety parameters not exceeding:- Ui: 11.4V, Ii: 0.2A, Pi: 0.51W.  Sensor can be installed with a cable length up to 1000m maximum from the amplifier, cable capacitance and inductance can be up to:- Capacitance: 200 nF max, Inductance: 810 μH max.

Approved amplifiers are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.


Dimensions

Body Diameter
35mm
Body Length (Flanged)
Travel: 51-70mm - Length: 141.3mm
Travel: 71-100mm - Length: 171.3mm
Body Length (Unflanged)
Travel: 51-70mm - Length: 125mm
Travel: 71-100mm - Length: 155mm
Push Rod Outside Diameter
6mm
Travel
Any stroke from 0-51mm to 0-100mm (e.g. 76mm)
Independent Linearity
<±0.25% at 20°C
<±0.1% available on request
Temperature Coefficient
<±0.01%/°C Gain & <±0.01%FS/°C Offset
Resolution
Infinite
Noise

<0.02% FSO

Frequency Response

>10KHz (-3dB)


Temperature Limits

Operating
-40 to +80°C
Storage
-40 to +125°C


Other

EMC Susceptibility
EN 61000-6-2
EMC Radiated
EN 61000-6-3
Vibration
IEC 68-2-6: 10g
Shock
IEC 68-2-29: 40g
MTBF
350,000 hrs 40°C Gf
Sealing
IP65/IP67 (connector) / IP67 (cable)
Electrical Connections
Screened cable or integral connector

Positek offers a range of options for its standard sensors. Each sensor is manufactured to suit each customer's preferences. If your requirement is outside the options given below, Positek can modify/ redesign a sensor to suit your specific requirement. Standard options are available as below:


Measurement Range

Factory set to any length from 0-51mm to 0-100mm in increments of 1mm. For example, if your application requires 3" (76 mm) measurement, then Positek will manufacture the sensor specifically for this length. The mechanical length and calibration will be set up for 76mm.


Connector/Cable Options

Option
Option Code
Connector - Hirschmann GD series Axial, IP65
J
Connector - Axial IP67, M12 - 4 pin. Without trim adjustment
J + Z600
Connector - Axial IP67, M12 - 4 pin. With trim adjustment J + Z601
Cable with axial M12 gland, IP67
L (3 core cable)
LQ (5 core cable)
(click for more information)
Cable with axial short gland, IP67
M (3 core cable)
MQ (5 core cable)
(click for more information)
Cable length - The standard length of cable supplied with a Positek position sensor is 50cm although you can specify any length you require up to a maximum of 15,000cm
Specified in cm after the L/LQ or M/MQ e.g. L200 for 200cm cable from axial cable gland


The sensor can be supplied without access to the two trim pots (gain and offset) with the adjustment holes sealed.
Option Code
Y


Mounting Thread Size Options

Option
Option Code
Front flange mount
N
Body clamps
P


Plunger Options

Option
Option Code
Spring loaded (extended)
R
Dome end on plunger
T
Non-captive plunger (not with options "R" or "T")
V

<+/-0.1% FSO Linearity error

Option Code
Z650

Click Here for approved Galvanic Isolation Amplifier Options



Galvanic Isolation Amplifier
Click for PDF
Outline
Click for PDF
Request AutoCAD Drawing
Datasheet
Click for PDF
Installation Sheet
Click for PDF


image missing