X500 Large Angle Rotary Sensor
ATEX & IECEx approved intrinsically safe sensors for hazardous gas environments
This sensor at a glance
Available in any measurement angle from 16 to 160° e.g. 90°
(for 5-15° range see X502)
Longer operating life than a potentiometer
Fast delivery options available
Body Diameter: 35mm
Sensor Mounting: Flange or servo
Spring loaded shaft option
Sealed to IP65/67 depending on connector/cable option
< ±0.25% up to 100°
< ±0.1 % option available
Temperature range: -40° to +80°C
The intrinsically safe X500 rotary sensor is ATEX and IECEx approved for use in potentially explosive gas/vapour atmospheres. It is designed for industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas. The X500, like all Positek sensors, is supplied with the output calibrated to the angle required by the customer, between 16 and 160 degrees and with full EMC protection built in. The sensor provides a linear output proportional with angle of rotation. There is a machined registration mark to identify the calibrated mid point.
Overall performance, repeatability and stability are outstanding over a wide temperature range. The X500 has long service life and environmental resistance with a rugged stainless steel body and shaft, the flange and servo mounts are anodised aluminium. The flange or servo mounting options make the sensor easy to install. Environmental sealing is to IP65 or IP67 depending on selected cable or connector options.
Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.
|ATEX/IECEx approval||The sensor is ATEX/IECEx approved to:|
Ex II 1G
Ex ia IIC T4 GA (Ta = -40°C to +80°C).
This designates the sensor as belonging to; Group II: suitable for all areas except mining, Category 1 G: can be used in areas with continuous, long or frequent periods of exposure to hazardous gas (Zone 0). Protection class ia, denotes intrinsically safe for all zones. Apparatus group IIC: suitable for IIA to IIC explosive gas. Temperature class T4: maximum sensor surface temperature under fault conditions 135°C. Ambient temperature range extended to -40°C to 80°C. Approval only applies to the specified ambient temperature range and atmospheric conditions in the range 0.80 to 1.10 Bar, oxygen <=21%.
|Galvanic Isolation Amplifier|
Intrinsically safe sensors must be used with a galvanically isolated amplifier with safety parameters not exceeding:- Ui: 11.4V, Ii: 0.2A, Pi: 0.51W. Sensor can be installed with a cable length up to 1000m maximum from the amplifier, cable capacitance and inductance can be up to:- Capacitance: 200 nF max, Inductance: 810 μH max.
Approved amplifiers are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
|Body Length (to seal face)||44mm|
|Shaft||15mm, OD 6mm|
For full mechanical details see drawing
|Measurement Range||Any angle from ±8° to ±80° |
|Independent Linearity||<±0.25% up to 100° at 20°C|
<±0.1% available on request
|Temperature Coefficient||<±0.01%/°C Gain & <±0.01%FS/°C Offset |
|Output Characteristics||See Graph|
|Operating||-40 to +80°C|
|Storage||-40 to +125°C|
|EMC Susceptibility||EN 61000-6-2|
|EMC Radiated||EN 61000-6-3|
|Vibration||IEC 68-2-6: 10g|
|Shock||IEC 68-2-29: 40g|
|MTBF||350,000 hrs 40°C Gf|
|Sealing||IP65 (connector) / IP67 (cable)|
|Electrical Connections||Screened cable or integral connector|
Positek offers a range of options for its standard sensors. Each sensor is manufactured to suit each customer's preferences. If your requirement is outside the options given below, Positek can modify/ redesign a sensor to suit your specific requirement. Standard options are available as below:
Factory set to any length from ±8° to ±80° in increments of 1°. For example, if your application requires 90° measurement, then Positek will manufacture the sensor specifically for this angular range. The sensor will measure 90° however will still rotate through 360°.
|Connector - Hirschmann GD series Axial, IP65||J|
|Connector - Axial, IP67, M12, 4 pin - without trim adjustment||J+Z600|
|Connector - Axial, IP67, M12, 4 pin - with trim adjustment||J+Z601|
|Cable with axial gland, IP67||L (3 core cable)|
LQ (5 core cable)
(click for more information)
|Cable with axial short gland, IP67||M (3 core cable)|
MQ (5 core cable)
(click for more information)
length - The standard length of cable supplied with a Positek position
sensor is 50cm although you can specify any length you require up to a
maximum of 15,000cm||Specified in cm after the L/LQ or M/MQ e.g. L200 for 200cm cable from axial cable gland|
|<+/-0.1% FSO Linearity error (100° max)||Option Code|