E138 Mid Stroke Slim-Line Linear Position Sensor
ATEX & IECEx approved intrinsically safe sensors for hazardous dust environments
This sensor at a glance
Available in any measurement range from 0-51mm to 0-100mm
(for 2-50mm range see E118)
Longer operating life than a potentiometer
Fast delivery options available
Body Diameter: 19mm
Sensor Mounting: Flange or Body Clamps
Spring loaded pushrod option available
Sealed to IP67
< ±0.1% option available
Temperature range: -40°C to +80°C
The intrinsically safe E138 is ATEX and IECEx approved for use in potentially explosive gas/vapour and dust atmospheres. The E138 is designed for a wide range of industrial applications and is ideal for OEMs seeking good sensor performance in situations where a small diameter, short-bodied sensor is required for operation in hazardous areas. The unit is compact and space-efficient, being responsive along almost its entire length, and like all Positek® sensors provides a linear output proportional to displacement. Each unit is supplied with the output calibrated to the travel required by the customer, from 0-51mm to 0-100mm and with full EMC protection built in. Overall performance, repeatability and stability are outstanding over a wide temperature range. The sensor has a compact 19 mm diameter stainless steel body, is easy to install and set up. The stainless steel mounting flange has two 3.2 mm by 30 degree wide slots on a 25 mm pitch. The stainless steel plunger can be supplied free or captive, with female M4 thread, or springloaded with a ball end. The E138 also offers a range of mechanical options, environmental sealing is to IP67.
Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.
The sensor is ATEX/ IECEx approved to:
Approval only applies to the specified ambient temperature range and atmospheric conditions in the range 0.80 to 1.10 Bar, oxygen <=21%.
|Galvanic Isolation Amplifier|
Intrinsically safe sensors must be used with a galvanically isolated amplifier with safety parameters not exceeding:- Ui: 11.4V, Ii: 0.2A, Pi: 0.51W. Sensor can be installed with a cable length up to 1000m maximum from the amplifier, cable capacitance and inductance can be up to:- Capacitance: 200 nF max, Inductance: 810 μH max.
Approved amplifiers are available from Positek; there is a
|Travel||Any stroke from 0-51mm to 0-100mm (e.g. 76mm)|
|Independent Linearity||<±0.25% at 20°C|
<±0.1% available on request
|Temperature Coefficient||<±0.01%/°C Gain & <±0.01%FS/°C Offset |
|Operating||-40 to +80°C|
|Storage||-40 to +125°C|
|EMC Susceptibility||EN 61000-6-2|
|EMC Radiated||EN 61000-6-3|
|Vibration||IEC 68-2-6: 10g|
|Shock||IEC 68-2-29: 40g|
|MTBF||350,000 hrs 40°C Gf|
|Electrical Connections||Screened cable or M8 4 pin|
Positek offers a range of options for its standard sensors. Each sensor is manufactured to suit each customer's preferences. If your requirement is outside the options given below, Positek can modify/ redesign a sensor to suit your specific requirement. Standard options are available as below:
Factory set to any length from 0-51mm to 0-100mm in increments of 1mm. For example, if your application requires 3" (76mm) measurement, then Positek will manufacture the sensor specifically for this length. The mechanical length and calibration will be set up for 76mm.
|Connector - Axial, IP67, M8 4 pin||J|
|Cable with axial gland, IP67||L (3 core cable)|
LQ (5 core cable)
(click for more information)
length - The standard length of cable supplied with a Positek position
sensor is 50cm although you can specify any length you require up to a
maximum of 15,000cm||Specified in cm after the L/LQ e.g. L200 for 200cm cable from axial cable gland|
Mounting Thread Size Options
|Front flange mount||N|
|Body clamps (see drawing)||P|
|Spring loaded (extended)||R|
|Dome end plunger||T|
|Non-captive plunger (not with options "R" or "T")||V|
|<+/-0.1% FSO Linearity error||Option Code|