E505 Slim-Line Rotary Sensor
ATEX & IECEx approved intrinsically safe sensors for hazardous dust environments
This sensor at a glance
Available in any measurement angle from 15 to 160°
Longer operating life than a potentiometer
Fast delivery options available
Body Diameter: 19mm
Sensor Mounting: Flange or servo
Compact and lightweight
Sealed to IP67
< ±0.25% up to 100°
< ±0.1 % option available
Temperature range: -40°C to +80°C
The intrinsically safe E505 is ATEX and IECEx approved for use in potentially explosive gas/vapour and dust atmospheres. The miniature design is well suited to automotive, industrial and scientific feedback applications and is ideal for OEMs seeking good sensor performance for arduous applications in hazardous areas.
As with all Positek sensors the E505 is supplied with the output calibrated to the angle required by the customer, between 15 and 160 degrees and with full EMC protection built in. The sensor provides a linear output proportional with angle of rotation. There is a machined registration mark to identify the calibrated mid point. Overall performance, repeatability and stability are outstanding over a wide temperature range. The E505 has long service life and environmental resistance with a rugged stainless steel body, flange and shaft. The flange or servo mounting options make the sensor easy to install, it also offers a range of mechanical options. Environmental sealing is to IP67.
Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier . Approved galvanic isolation amplifiers (X005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.
The sensor is ATEX/ IECEx approved to:
Approval only applies to the specified ambient temperature range and atmospheric conditions in the range 0.80 to 1.10 Bar, oxygen <=21%.
|Galvanic Isolation Amplifier|
Intrinsically safe sensors must be used with a galvanically isolated amplifier with safety parameters not exceeding:- Ui: 11.4V, Ii: 0.2A, Pi: 0.51W. Sensor can be installed with a cable length up to 1000m maximum from the amplifier, cable capacitance and inductance can be up to:- Capacitance: 200 nF max, Inductance: 810 μH max.
Approved amplifiers are available from Positek; there is a
|Body Length (to seal face)||45.4mm|
|Shaft||8mm, OD 4mm|
For full mechanical details see drawing
|Measurement Range||Any angle from ±7.5° to ±80° |
|Independent Linearity||<±0.25% up to 100° at 20°C|
<±0.1% available on request
|Temperature Coefficient||<±0.01%/°C Gain & <±0.01%FS/°C Offset |
|Output Characteristics||See Graph|
|Operating||-40 to +80°C|
|Storage||-40 to +125°C|
|EMC Susceptibility||EN 61000-6-2|
|EMC Radiated||EN 61000-6-3|
|Vibration||IEC 68-2-6: 10g|
|Shock||IEC 68-2-29: 40g|
|MTBF||350,000 hrs 40°C Gf|
|Electrical Connections||Screened cable or 4 pin connector|
Positek offers a range of options for its standard sensors. Each sensor is manufactured to suit each customer's preferences. If your requirement is outside the options given below, Positek can modify/ redesign a sensor to suit your specific requirement. Standard options are available as below:
Factory set to any length from ±7.5° to ±80° in increments of 1°. For example, if your application requires 90° measurement, then Positek will manufacture the sensor specifically for this angular range. The sensor will measure 90° however will still rotate through 360°.
|Connector, Axial, IP67 M8 4 pin||J|
|Cable with axial gland, IP67||L (3 core cable)|
LQ (5 core cable)
(click for more information)
|Cable length - The standard length of cable supplied with a Positek position sensor is 50cm although you can specify any length you require up to a maximum of 15,000cm||Specified in cm after the L/LQ e.g. L200 for 200cm cable from axial cable gland|
|<+/-0.1% FSO Linearity error (100° max)||Option Code|