This sensor at a glance
Available in any measurement angle from 15° to 160°
Longer operating life than a potentiometer
Fast delivery options available
Body Diameter: 19mm
Sensor Mounting: Flange or servo
Compact and lightweight
Sealed to IP67
< ±0.25% up to 100°
Temperature range: -40°C to +80°C
Intrinsically safe H505 is CSA approved for use in potentially explosive gas/vapour and dust atmospheres. The H505 is an affordable, durable, high-accuracy rotary sensor designed for industrial and scientific feedback applications, but requires a smaller footprint than the H500.
Like all Positek® sensors, the H505 provides a linear output proportional with angle of deflection. Each unit is supplied with the output calibrated to the angle required by the customer, between 15 and 160 degrees and with full EMC protection built in.
It is particularly suitable for OEMs seeking good sensor performance for applications where space is important.
Overall performance, repeatability and stability are outstanding over a wide temperature range. The H505 has long service life and environmental resistance with stainless steel body parts. The flange or servo mounting options make the sensor easy to install, the flange has two 3.2mm by 30 degree wide slots on a 25mm pitch. The H505 also offers a range of mechanical and electrical options. Environmental sealing is to IP67.
Positek intrinsically safe sensors are designed to be used with a galvanically isolated amplifier. Approved galvanic isolation amplifiers (G005) are available from Positek; there is a choice of 0.5-9.5V or 4-20mA transmission outputs.
The sensor can be installed with a cable length up to 1km between the sensor and the amplifier.
This sensor is CSA approved to; Class I, Zone 0
|Galvanic Isolation Amplifier||It
is imperative Positek® intrinsically safe sensors be used in
conjunction with a galvanic barrier to meet the requirements of the
product certification. The Positek G005 Galvanic Isolation Amplifier is
purpose made for Positek IS sensors making it the perfect choice. Refer
to the G005 datasheet for product specification and output configuration
The Positek® G005 Galvanic Isolation Amplifier is available with 0.5 - 9.5V or 4 - 20mA transmission output options or reverse outputs of 9.5 - 0.5 volts or 20 - 4 mA.
|Body Length (to seal face)
||8mm, OD 4mm
For full mechanical details see drawing
||Any angle from ±7.5° to ±80°
||<±0.25% up to 100° at 20°C
||<±0.01%/°C Gain & <±0.01%FS/°C Offset
||-40 to +80°C
||-40 to +125°C|
||IEC 68-2-6: 10g
||IEC 68-2-29: 40g|
||350,000 hrs 40°C Gf
||Screened cable or M8 4 pin connector
Positek offers a range of options for its standard sensors. Each sensor is manufactured to suit each customer's preferences. If your requirement is outside the options given below, Positek can modify/ redesign a sensor to suit your specific requirement. Standard options are available as below:
Factory set to any length from ±7.5° to ±80° in increments of 1°. For example, if your application requires 90° measurement, then Positek will manufacture the sensor specifically for this angular range. The sensor will measure 90° however will still rotate through 360°.
|Connector, Axial IP67 M8 4 pin||J|
|Cable with axial gland, IP67||L (3 core cable)|
LQ (5 core cable)
(click for more information)
|Cable length - The standard length of cable supplied with a Positek position sensor is 50cm although you can specify any length you require up to a maximum of 15,000cm||Specified in cm after the L/LQ e.g. L200 for 200cm cable from axial cable gland|